How to sew a zipper into a knitted product: options for a knitted sweater and a knitted bag

Sewing a zipper into a knitted product is not easy!

This work requires patience and skill. Today we will tell you about a method for connecting a zipper to a jacket using a hook. The method shown greatly simplifies the task and gives excellent results.

I suggest you get acquainted with the following technology. Necessary materials:

Zipper of appropriate length
Pencil
Paper
Knitting needle for lifting stitches.
A knitting needle that was used to knit a product.
The yarn from which the product was knitted
Scissors
Large tapestry or darning needle

Step one: place the paper on the wrong side of the product and, using a pen or felt-tip pen, mark the distance between the wrong rows.

Step two: transfer these markings onto the zipper tape using a pencil or marker.

Step Three: Using a knitting needle, draw a loop of yarn through the first pencil mark of the zipper.

Step four: Insert the knitting needle into the loop and pull the loop up to match the size of the knitted loop.

Step five: remove the knitting needle and through the resulting loop, knit the next one, extended through the second marking on the zipper.

And again insert the knitting needle into the loop, thereby ensuring the uniformity of the knitted chain and its correspondence to the rows on the product.

Continue this work until you have followed the markings on both sides of the zipper.

Step six: thread the yarn into a large needle and sew the zipper to the product, grabbing one loop at a time on the product and on the zipper until the work is completed
The clasp is successfully sewn
You can also sew a zipper into a sweater using a needle, which you can read about in the article How to sew a zipper into a knitted sweater. Method two
Did you like the advice and was it useful to you?

Source: https://babairisha.ru/kak-vshit-molniyu-v-koftu/

My Master Classes: sewing a lock into a knitted blouse

After bragging about filming in the program "Affairs" of the country, mom rimston1 Rimma placed an order for us to knit a blouse with a hood for her son in a very cheerful color. Kofteika contacted, went to the owner, and even the report has already been received and published here. I won’t describe the knitting (in this new interface, the first version of the message was lost somewhere... so I’m writing the second time quickly, to the point and without preamble. For anyone interested in the basic parameters of the blouse, they are here)

I have been asked many times how I sew a lock into a knitted item. Based on this blouse, I decided to share some wisdom with you.

In general, when knitting a sweater, into which, according to the idea, a lock should be sewn, along the edge (at a distance of about 1.5-2 cm) I knit a path of purl loops on the front side of the product (i.e. in the purl row we knit one knit stitch, and in the front row we always knit the same loop purl).

If you already knitted a blouse at the time of viewing this MK, do not be upset. You can unravel one loop along the length of the entire product and lift it with a crochet hook.

If at the bottom of the product there is a 1x1 elastic band like mine, then just the fifth loop from the beginning of the row will be needed (edge, knit, purl, knit, purl,

facial, etc...)

What is good about this method (by the way, I came up with it myself and please do not accuse me of plagiarism) is that on the front side (thanks to the recessed purl loop) the cast-on row for the edge is not visible, but on the reverse side a very convenient chain of cast-on stitches

Now we take a circular knitting needle 1-1.5 sizes larger than we knitted the main fabric (in my case, I knitted with a 3-knit, but I cast on 4.5 knitting needles, 80 cm fishing line, ADDI-click). This is done so that the canvas does not tighten and looks neat. Next, we put on the knitting needle the half-loop of the knit chain closest to the edge. Like this:

We attach the thread and knit with front and back rows to the desired height (i.e. when the knitted strip is equal in height to the edge of the product):

Without breaking the thread, we lift the chain from the front side of the product by the outer loops along the entire height of the product and close it in a circle.

We knit another 4-5 circular front rows (about 1-1.5 cm) necessary for sewing in the lock and close the loops with a crochet hook. Use a larger hook to avoid pulling the edge again.

We perform the same actions with the other shelf at the front of the product. By the way, if you are not too lazy, you can knit a protection against the lock, so that the child does not pinch the skin with the lock, in rotating rows at the top on one of the shelves. like this:

We steam it (if the product is made of cotton) and take it to a specialist to sew in the lock. Or we do it ourselves.

I hope my MK was useful to you. Thank you for your attention!

By the way, if you are not lazy and want to sew a lock in a very, very difficult way, then there is an excellent MK from the craftswoman bobignu. I liked the quality of the photo and the thoroughness, as well as the text...

Source: https://mamaasja.blogspot.com/2012/04/blog-post_10.html

How to make original fasteners for knitted items?

The name of such an original fastener - brakes - came into fashion from marine terminology. In the Marine Dictionary we read:

Indeed, it makes sense. Yes, and in appearance too.

To make such a fastener, you can use various cords, braid, soutache, yarn, pieces of fabric, leather, suede, felt, and, in fact, buttons. As a rule, cone-shaped buttons are chosen for braking. But this rule is purely advisory.

There may be several buttons or even one. And to support the overall stylistic decision, it can be made from the same material as the brake itself. For example, make a knitted button.

Such a fastener will decorate outerwear in an original way not only for the fair sex, but will also look stylish in men's sets.

In addition, wicker decorative details can make women's accessories unique: cosmetic bags , handbags , clutches .

The brake clasp can be from the simplest minimalist form to sophisticated “intricacies”. Therefore, if you set out with your own hands , then follow the proven principle: from simple to complex. Start with the simplest brake forms. For example, from these:

Ornate brakes aren't that hard to do either. The main thing here is attentiveness and perseverance.

Now you know how to make a stylish brake clasp with your own hands.
Charge yourself with positivity, and you will succeed!

Source: https://www.bolshoyvopros.ru/questions/1656450-kak-sdelat-originalnye-zastezhki-dlja-vjazanoj-veschi.html

Features of sewing hidden fasteners into parts made of thin fabrics

When choosing a location for the fastener, you need to remember that it will look different on fabrics with different characteristics. For example, it is better not to insert a zipper into the side seam of a dress made of thin, light and delicate material - the flank may “lead”. In this case, the center line of the back will be a more practical and easier to implement option. If the material is loose or airy, the seam allowances should be additionally reinforced with non-woven fabric.

season.ru

On items made of particularly thin fabric (such as chiffon), it is not recommended to sew zippers in one layer. There is a danger that it will pull back the material or become noticeable. Therefore, a special lining is needed. Along the zipper line it is fastened to the main fabric, and below the end of the zipper it is left free to maintain the flowing hemline.

How to make a French seam below the end of the lock:

fold the pieces of light main fabric with the wrong sides facing each other and stitch, retreating from the cut at a distance of about 7 mm;
bring the line to the end of the tape - to the edge at the allowance (you don’t have to make cuts along the bulk material);
trim the allowances and press the seam so that they remain on the inside;
lay the line straight, retreating from the edge up to 7 mm and finish it 30 mm further than the first;
Press seam allowances in one direction, and press above it.

You will need to make a French seam along the cover - there should be a transverse bartack at the end. On the lining, the allowance is cut to connect the two types of fabric. That’s why the fastener is needed - it will prevent the edges from “spilling out.” With a little practice, you will be able to sew hidden zippers onto dresses, skirts and other items, no matter the fabric, and add a useful skill to your professional tailoring arsenal.

odeon1.ru

How to sew a zipper into a knitted product: step-by-step description

1001 Article author: Reading time: 1 min.

What you need for work

For any work, the starting point is the preparatory stage. In this process, it consists of the following steps.

Product preparation . The item must be subjected to wet heat treatment and ironed. This is especially true for crocheted fabric.
Fixing the fastener using safety pins or other elements.
Perform other steps depending on the fastening method: knitting the strap, knitting a track of air loops on the fastener, making an auxiliary seam .

What you need for work

Before you begin the main work, you should start with the preparatory stage:

Prepare the product. The item of clothing must be processed and ironed. In particular, this applies to fabric crocheted:
Next, you need to secure the fasteners using regular pins or other devices;
The next steps to be performed directly depend on the fixation method, namely: creating a strip, knitting a strip, etc.

Knitted sweaters with a zipper look as if they are seamlessly knitted and do not require additional decorations

Important! It is worth paying extra attention to the peculiar allowances; their size is 5 mm with the basic version of the fastener.

It is also necessary to prepare materials and tools. Among them:

Knitting needles and devices for fixation;
Needle and thread to match the color of the product;
Paper and a simple pencil.

Children's knitted vest with clasp

Learning to sew a zipper into knitted items

If you want to give your jacket a neat and stylish look, we recommend that you sew in a double placket. There is also another knitting option - this is a hollow elastic band.

https://www.youtube.com/watch?v=n7xCXeNElLc

We sew a zipper into the finished knitted sweater.

In order to get started, you should first stock up on certain items: yarn, two straight knitting needles, a needle, a tailoring meter, cotton threads that match the color of your sweater, a sewing machine, scissors, as well as the zippers themselves. Often, various sequins are used for decoration, which can also be beautifully sewn onto a knitted item.

When starting to cut out a jacket, you should immediately very accurately calculate the width of both the right and left shelves. This is important, because it is necessary to leave a reserve for the knitted strap so that you can then sew in a zipper.

Before you start making the zipper placket, you should knit a sample, and this should be done using stockinette stitch, which has a length of 10 cm. Next, measure the length from the bottom of the blouse to the top of the collar.

This distance will be considered the length of the prepared strip.

It is important not to forget to turn the product inside out and cast on loops to complete the bottom layer of the plank. The double plank to the right of the shelf is made in the same way. It is important that absolutely all details must be made symmetrically! Nothing should be tight or puffy.

Next, take the zipper and unfasten it. After this, you need to insert both halves into the double bar. Basting should be done with threads that contrast with the main color of the blouse.

Now check whether the basted lock fits correctly, that is, try to open it and then close it. If everything is correct, then start sewing the zipper with threads that will match the color of the product.

There is also an equally interesting option - this is a hollow elastic band. Here you first need to count a certain number of loops that you cast on according to the pattern of the front stitch. Next, you should multiply this figure by two.

You need to alternate in the first row as follows: first there is one front loop, we remove the second one without knitting. Remember, the thread in working condition must certainly be in front of the loop!

In subsequent rows, the loops that we remove need to be knitted.
The zipper is sewn to the product from below.

Source: https://sigolki.com/vyazanie/dlya-zhenshhin/uchimsya-vshivat-molniyu-v-vyazanye-veshhi.html

What will you need for work?

In order to transform your old, once beloved, but tired jumper, you will need the following:

lightning, the larger its teeth, the better;
scissors, threads and needles;
tailor's pins;
adhesive backing tape (web);
iron;
satin or other narrow ribbon, braid.

In this case, a sewing machine is not required to update the jumper.

If the chosen beautiful decorative zipper turns out to be longer than necessary, it will have to be cut. To do this, you will need tools, depending on the type of zipper.

When toothpaste is harmful to children: permissible age doses

The star of the series “Sultan of My Heart” spoke about the choice of his future wife

“Olga” from the series of the same name: the tragic fate of actress Yana Troyanova

Sewing a zipper into a knitted sweater

How to sew a zipper on a knitted item? Sewing a regular zipper in itself is not a difficult job, but joining it with knitwear requires patience. Sewing a zipper onto a tightly knit sweater is one of the most time-consuming tasks and sometimes intimidating for beginners.

To be honest, specialists also do not like to do this work, as it takes a lot of time. But since the lightning has broken down, you still have to do it.

How to properly sew a zipper with your own hands so that it turns out beautifully and evenly? You will learn about this further.

Useful tips

In order to avoid difficulties during work and do it better, you should pay attention to some tips that will help you avoid mistakes and contribute to high-quality work, namely:

The zipper lock should be chosen exactly to match the color of the desired product. This way the zipper will not stand out from the general appearance and will look attractive even if it is sewn along the entire length of the knitted product;
The upper border of the zipper must be at the level of the collar, and in case of a mismatch in size, the excess must be cut off;

Fastener after completing the entire sewing procedure

It is advisable to secure the fastener to clothing using hand stitches. It should be sewn on with two lines on a machine, one of them should be at a distance of about three millimeters from the edge, and the second about six;
In cases where additional fixation is needed, you can use safety pins, which should not be removed when using a sewing machine;

Pulling yarn through the clasp strip using a crochet hook

To ensure that the dog does not interfere during work, you should remove the foot and return it back after completing the work;
After completing the work done, it is necessary to remove the remaining threads from hand stitches, and to consolidate the result, go over the seams with an iron;
It is also important not to forget to leave small pieces of the zipper to decorate its edges.

Working with a small fastener

It is not at all necessary to go to a studio and spend money to sew in a zipper, but to do this procedure yourself at home. Such an activity may at first seem difficult and time-consuming, but each time the experience will increase, and thereby the work will become easier. You just need to stick to technology and have a little free time.

Sewn-in clasp on the inside

Now it’s clear how to sew a zipper to a knitted product and what you will need for this. The process, contrary to what many people expect, is simple and will not spoil the appearance of the knitted material. On the Internet you can find a large number of master classes on this lesson.